# No PTT on new Digirig DR-891
**URL:** https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856
**Category:** Uncategorized
**Tags:** hardware-dr-891, yaesu-ft-891
**Created:** [June 25, 2024, 5:57pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856 "2024-06-25T17:57:03Z")
**Posts on this page:** 8
**Page:** 1
### Author:  [@NQ7K](https://forum.digirig.net/u/NQ7K)
#### Post date: [June 25, 2024, 5:57pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/1 "2024-06-25T17:57:04Z")
Greetings,
Subject line says it all…while I do have CAT control none of the PTT settings will key the radio. I also tried swapping the audio cable and I took the DR apart and checked the pads on the circuit board.
Any info appreciated. 🙂
Mike
NQ7K
---
### Author:  [@Constrainted](https://forum.digirig.net/u/Constrainted)
#### Post date: [June 25, 2024, 8:28pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/2 "2024-06-25T20:28:58Z")
I don’t have the radio, but I don’t want you post to go too long without a response.
> [@Cables for Yaesu FT-891](https://forum.digirig.net/t/cables-for-yaesu-ft-891/16):
>
> Unlike other transceivers in FT-8xx lineup, Yaesu FT-891 does not expose the serial interface lines and instead implements serial CAT internally via its own USB connection. Only the cable with MiniDin6 connector is needed on the transceiver side. Plugged into Digirig’s audio port it takes care of minimum feature set required for digital modes: audio and PTT. The PTT switch is controlled via the RTS signal of Digirig’s COM port. The cable is available as part of [Yaesu FT-8xx cables kit](https://digirig.net/product/yaesu-ft-8xx-cords-for-digirig-mobile/). If opt…
73 Constrainted
---
### Author:  [@K0TX](https://forum.digirig.net/u/K0TX)
#### Post date: [June 25, 2024, 9:46pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/3 "2024-06-25T21:46:00Z")
Mike,
What is the application you are trying to configure?
DR-891 supports PTT through radio’s CAT control, PTT via GPIO3 of the codec and VOX PTT on the right audio channel.
---
### Author:  [@NQ7K](https://forum.digirig.net/u/NQ7K)
#### Post date: [June 25, 2024, 11:44pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/4 "2024-06-25T23:44:32Z")
Hi Denis,
I was using Winlink for the configuration, and I tried everything to the point of having to walk away from it. I went and had some lunch, came back and reconfigured and it’s working.
I wish I could give you a definitive solution to the issue that could be passed on to others but I honestly have no idea. 😊
On my original Digirig I had audio to Com3 and CAT to Com6 and now the new one uses Com6.
I do have one more issue that needs resolution and that is transmit power seems to be lower in Data mode than before.
I have the power set to 30 watts and if I key up in CW mode the wattmeter in the tuner shows that but in Data mode it only shows around 5 watts.
I’ll figure it out tomorrow. 😊
Thanks for jumping in, and great idea on the new DR for the 891 😊
Mike
---
### Author:  [@webmonkey](https://forum.digirig.net/u/webmonkey)
#### Post date: [June 26, 2024, 1:52pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/5 "2024-06-26T13:52:44Z")
my thoughts are:
even though you have same radio and computer, your box in between is different.
this causes your computer to see ‘new’ coms/audio devices.
try double checking the ‘identity’ of the audio device and adjust the audio levels.
(my thought on the lower ‘drive’/‘output’ going from cw to data)
good luck
kb0wlf
---
### Author:  [@Constrainted](https://forum.digirig.net/u/Constrainted)
#### Post date: [June 26, 2024, 3:58pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/6 "2024-06-26T15:58:12Z")
> [@NQ7K](#):
>
> I have the power set to 30 watts and if I key up in CW mode the wattmeter in the tuner shows that but in Data mode it only shows around 5 watts.
What are the transmit bandwidths for CW and Data mode? On one of my radios, which shows TX bandwidth, they can be different by a factor of 5.
73 Constrainted
---
### Author:  [@K6IRK](https://forum.digirig.net/u/K6IRK)
#### Post date: [June 27, 2024, 10:45pm UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/7 "2024-06-27T22:45:52Z")
I just got mine too, the cables that came with it, I have CAT Control, but No PTT. Its Com 4 & 5, same as my older Digirig. But my older one was running on Com 4 & 12 using WSJT
This is my current setting using WSJT which works with the other Digirig with the separate CAT control.
I even tried removing the one cable for USB-A from the radio and I got nothing, errors like crazy.
Anyone able to get this to work by chance? I also called and left a message along with a support message too.
73 Rob - K6IRK
---
### Author:  [@K0TX](https://forum.digirig.net/u/K0TX)
#### Post date: [June 28, 2024, 10:50am UTC](https://forum.digirig.net/t/no-ptt-on-new-digirig-dr-891/3856/8 "2024-06-28T10:50:19Z")
Rob,
DR-891 makes use of the serial port inside of the radio. Unlike the serial port in Digirig Mobile, the one in the radio doesn’t use RTS signal for hardware PTT. In your setup with DR-891 please set PTT method to CAT. VOX can also be an option (less desirable) if you configure WSJT-X to send the payload to both right and left audio channels.