# Order Question - Ordered CAT - Default Logic - Received RS-232
**URL:** https://forum.digirig.net/t/order-question-ordered-cat-default-logic-received-rs-232/2682
**Category:** Uncategorized
**Tags:** yaesu-ftm-400xdr, troubleshoot-serial
**Created:** [November 22, 2023, 5:56pm UTC](https://forum.digirig.net/t/order-question-ordered-cat-default-logic-received-rs-232/2682 "2023-11-22T17:56:16Z")
**Posts on this page:** 5
**Page:** 1
### Author:  [@jwestmoreland](https://forum.digirig.net/u/jwestmoreland)
#### Post date: [November 22, 2023, 5:56pm UTC](https://forum.digirig.net/t/order-question-ordered-cat-default-logic-received-rs-232/2682/1 "2023-11-22T17:56:16Z")
Hello,
Not sure if posting here is the most appropriate place - but on my order - it clearly said CAT - Logic Level - and I received a unit that says RS-232 written in silver ink on the box.
Right now - I have to assume this is a mistake since I didn’t order the RS-232 option and my rig is not one of the ones listed for RS-232.
So, should this unit be RMA’ed so I can get what was actually placed on my order?
Thanks,
John W.
---
### Author:  [@K0TX](https://forum.digirig.net/u/K0TX)
#### Post date: [November 22, 2023, 6:07pm UTC](https://forum.digirig.net/t/order-question-ordered-cat-default-logic-received-rs-232/2682/2 "2023-11-22T18:07:46Z")
John,
Your order contained Digirig and CAT capable MiniDin10 cable and no other transceiver cables. MiniDin10 cables are used with Yaesu FTM radios with RS-232 serial port. That being your first order I figured the probability is high that you intend to use the kit with Yaesu FTM so the swap was done as a courtesy to save you the potential hassle and frustration.
Here is the relevant discussion on the topic of FTM:
> [@Readout of FTM-6000 with YAESU miniDin10 &CAT cable gives 'Format error'](https://forum.digirig.net/t/readout-of-ftm-6000-with-yaesu-minidin10-cat-cable-gives-format-error/1172):
>
> Connected green plug of YAESU DATA&CAT cable to serial socket of digirig. Started ADMS-13 SW and tried to readout FTM-6000. TRX goes into mode ‘CLN Tx’ as described. When RX is started in ADMS-13 and then the DIAL button on the TRX is pressed, ADMS-13 immediately says ‘Format Error’. On the TRX, the message ‘SND.ERR’ appears. The COM port on the PC is recognized properly and it is correctly set in ADMS-13. Tried several baud rates and with/without HW-handshake. No luck. Has anybody been success…
If my assumption was incorrect, I apologize for that and will be happy to arrange the replacement or instruct you on changing the serial port configuration.
PS: I also received all your emails re. this matter.
---
### Author:  [@jwestmoreland](https://forum.digirig.net/u/jwestmoreland)
#### Post date: [November 22, 2023, 6:14pm UTC](https://forum.digirig.net/t/order-question-ordered-cat-default-logic-received-rs-232/2682/3 "2023-11-22T18:14:58Z")
Hello Denis,
Thanks for that - I just need to dial in getting GPIO control for PTT.
I’ll look at what I need to do.
Thanks!
John
---
### Author:  [@K0TX](https://forum.digirig.net/u/K0TX)
#### Post date: [November 22, 2023, 6:16pm UTC](https://forum.digirig.net/t/order-question-ordered-cat-default-logic-received-rs-232/2682/4 "2023-11-22T18:16:51Z")
John,
PTT is independent from the serial lines configuration and controlled by RTS signal.
Here’s the info on the subject:
[ ](https://www.youtube.com/watch?v=1EtrkyisCnc)
---
### Author:  [@jwestmoreland](https://forum.digirig.net/u/jwestmoreland)
#### Post date: [November 22, 2023, 6:41pm UTC](https://forum.digirig.net/t/order-question-ordered-cat-default-logic-received-rs-232/2682/5 "2023-11-22T18:41:08Z")
Denis,
Great - I’ll look at this a little later today.
Thanks For Your Help!
73’s,
John